ZyXEL 91-005-124003B Datasheet download pdf (Page 103)

G-1000 User’s Guide

Chapter 13 LAN Setup 103

13.3.1 Configuring MAC Address Filter

Your G-1000 checks the MAC address of the wireless station device against a list of allowed

or denied MAC addresses. However, intruders could fake allowed MAC addresses so MAC-

based authentication is less secure than EAP authentication.

Follow the steps below to create the MAC address table on your G-1000.

Key 1 to Key 4 The WEP keys are used to encrypt data. Both the G-1000 and the wireless stations must

use the same WEP key for data transmission.

If you chose 64-bit WEP in the WEP Encryption field, then enter any 5 ASCII characters

or 10 hexadecimal characters ("0-9", "A-F").

If you chose 128-bit WEP in the WEP Encryption field, then enter 13 ASCII characters or

26 hexadecimal characters ("0-9", "A-F").

Note: Enter “0x” before the key to denote a hexadecimal key. Don’t enter

“0x” before the key to denote an ASCII key.

Authen. Method Press [SPACE BAR] to select Auto, Open System Only or Shared Key Only and press

[ENTER].

This field is N/A if WEP is not activated.

If WEP encryption is activated, the default setting is Auto.

Edit MAC Address Filter Press [SPACE BAR] to select Yes and press [ENTER] to display Menu 3.5.1 - WLAN

MAC Address Filter.

Edit Roaming

Configuration

Press [SPACE BAR] to select Yes and press [ENTER] to display Menu 3.5.2 - Roaming

Configuration.

Block Intra-BSS Traffic Intra-BSS traffic is traffic between wireless stations in the same BSS. Select No to allow

Intra-BSS traffic, select Yes to block all Intra-BSS traffic.

Preamble Select a preamble type from the drop-down list menu. Choices are Long, Short and

Dynamic. The default setting is Long.

See the section on preamble for more information.

802.11 Mode Select B Only to allow only IEEE 802.11b compliant WLAN devices to associate with the

G-1000.

Select G Only to allow only IEEE 802.11g compliant WLAN devices to associate with the

G-1000.

Select Mixed to allow either IEEE802.11b or IEEE802.11g compliant WLAN devices to

associate with the G-1000. The transmission rate of your G-1000 might be reduced.

Max. Frame Burst Enable Maximum Frame Burst to help eliminate collisions in mixed-mode networks

(networks with both IEEE 802.11g and IEEE 802.11b traffic) and enhance the

performance of both pure IEEE 802.11g and mixed IEEE 802.11b/g networks. Maximum

Frame Burst sets the maximum time, in microseconds, that the G-1000 transmits IEEE

802.11g wireless traffic only.

Type the maximum frame burst between 0 and 1800 (650, 1000 or 1800 recommended).

Enter 0 to disable this feature.

Breathing LED Select Yes to enable the Breathing LED, also known as the G-1000 LED.

The blue G-1000 LED is on when the G-1000 is on and blinks (or breaths) when data is

being transmitted to/from its wireless stations. Clear the check box to turn this LED off

even when the G-1000 is on and data is being transmitted/received.

When you have completed this menu, press [ENTER] at the prompt “Press ENTER to confirm or ESC to cancel” to

save your configuration or press [ESC] to cancel and go back to the previous screen.

Table 43 Menu 3.5 Wireless LAN Setup

FIELD DESCRIPTION

1 2 ... 98 99 100 101 102 103 104 105 106 107 108 ... 191 192

ZyXEL 91-005-124003B Datasheet Page 103

Comments to this Manuals

ZyXEL 91-005-124003B Datasheet Page 103

Comments to this Manuals

Related products and manuals for WLAN access points ZyXEL 91-005-124003B