ZyXEL IES-612-51A User Manual Page 293
- Page / 444
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 44 DHCP Commands
IES-612-51A User’s Guide
293
where
This command has no effect if the relaymode is both. If the relaymode is auto, this command
specifies to which DHCP server (the primary one or the secondary one) the IES-612-51A
should relay DHCP requests for the selected VLAN.
44.1.7 Relaymode Command
Syntax:
ras> switch dhcprelay relaymode <mode>
where
This command controls how the IES-612-51A routes DHCP requests. The IES-612-51A can
route DHCP requests to the active DHCP server for the VLAN, or it can route DHCP requests
to all DHCP servers set up for the VLAN.
44.2 DHCP Relay Option 82 (Agent Information) Sub-option 1
(Circuit ID)
Use the following commands to configure the DHCP relay Option 82 (agent information)
feature, sub-option 1. This feature applies regardless of whether or not the DHCP relay is on.
44.2.1 Option 82 Sub-option 1 Enable Command
Syntax:
ras> switch dhcprelay option82 enable
This command turns on the DHCP relay agent information (Option 82 Sub-option 1) feature.
<vid> =
The ID of the VLAN served by the specified DHCP
server(s).
<active-server> =
1: The primary DHCP server is active.
2: The secondary DHCP server is active.
<mode> =
relay process mode; it controls to which DHCP server(s) the
IES-612-51A relays DHCP requests.
auto - the IES-612-51A relays DHCP requests to the active
server for each VLAN
both - the IES-612-51A relays DHCP requests to the
primary and secondary server for each VLAN, regardless of
which one is active
- IES-612-51A 1
- About This User's Guide 3
- Document Conventions 4
- Icons Used in Figures 5
- Safety Warnings 6
- Safety Warnings 7
- Contents Overview 9
- Table of Contents 11
- Chapter 43 19
- Chapter 44 19
- Chapter 48 21
- Chapter 49 21
- Chapter 53 23
- Chapter 54 24
- Chapter 55 25
- Chapter 56 25
- List of Figures 27
- List of Tables 35
- Introduction 39
- CHAPTER 1 41
- 1.2.2 Curbside Application 42
- CHAPTER 2 45
- Figure 5 Rack Mounting 47
- CHAPTER 3 49
- 3.2.1 Console Port 50
- 3.2.4 Telco-50 Cables 51
- 3.2.5 Telco-50 Connections 52
- 3.2.6 ADSL Connections 52
- 3.2.7 Typical MDF Scenarios 53
- Chapter 3 Front Panel 54
- Chapter 3 Front Panel 55
- Basic Settings 59
- CHAPTER 4 61
- Figure 15 Login 62
- Figure 16 Home 62
- 4.4 Navigation Panel 63
- 4.5 Changing Your Password 65
- Figure 18 User Account 66
- Figure 19 Logout 67
- CHAPTER 5 69
- Figure 21 xDSL Port Setup 70
- Figure 22 VC Setup 71
- Figure 23 VC Setup, Delete 71
- Figure 24 Select Ports 71
- Figure 25 VC Setup 72
- Figure 26 VC Setup 72
- Figure 27 Select Ports 73
- Figure 28 VC Setup 73
- Figure 29 Config Save 73
- CHAPTER 6 75
- Table 5 Home (continued) 76
- 6.1.3 RMON Statistics Screen 81
- 6.1.4 RMON History Screen 83
- CHAPTER 7 87
- Chapter 7 System Information 88
- Table 11 System Info 88
- Chapter 7 System Information 89
- CHAPTER 8 91
- Chapter 8 General Setup 92
- CHAPTER 9 93
- 9.2 Authentication Screen 94
- Chapter 9 User Account 95
- Table 14 User Account 95
- Chapter 9 User Account 96
- CHAPTER 10 97
- 10.3 Switch Setup Screen 99
- Chapter 10 Switch Setup 100
- IES-612-51A User’s Guide 100
- Figure 43 Switch Setup 100
- Table 15 Switch Setup 100
- Chapter 10 Switch Setup 101
- CHAPTER 11 103
- Chapter 11 IP Setup 104
- CHAPTER 12 105
- Chapter 12 ENET Port Setup 106
- CHAPTER 13 107
- 13.4 Interleave Delay 108
- 13.6 Default Settings 109
- 13.7 xDSL Port Setup Screen 109
- Chapter 13 xDSL Port Setup 110
- Figure 47 Select Ports 110
- Chapter 13 xDSL Port Setup 111
- Figure 48 xDSL Port Setting 112
- Table 20 xDSL Port Setting 112
- 13.8 Virtual Channels 115
- 13.9 VC Setup Screen 116
- Figure 49 VC Setup 117
- Table 21 VC Setup 117
- Figure 51 Select Ports 119
- 13.10 Priority-based PVCs 120
- 13.11 PPVC Setup Screen 121
- Figure 54 PPVC Setup, Edit 122
- Table 24 PPVC Setup, Edit 123
- CHAPTER 14 125
- 14.2 ATM QoS 127
- 14.3 Traffic Shaping 128
- 14.4 Upstream Policing 130
- 14.5 VC Profile Screen 131
- 14.6 Alarm Profile Screen 133
- 14.7 IGMP Filtering 134
- CHAPTER 15 137
- 15.2 xDSL Performance Screen 138
- Chapter 15 xDSL Line Data 139
- Figure 62 xDSL Performance 139
- Table 30 xDSL Performance 139
- 15.3 xDSL Line Data Screen 140
- Figure 63 xDSL Line Data 141
- Chapter 15 xDSL Line Data 142
- Table 31 xDSL Line Data 142
- PART III 143
- CHAPTER 16 145
- 16.3 VLAN Status Screen 146
- Chapter 16 VLAN 147
- Figure 64 VLAN Status 147
- Table 32 VLAN Status 147
- Chapter 16 VLAN 148
- Figure 66 VLAN Port Setting 150
- Table 34 VLAN Port Setting 150
- Figure 67 Select Ports 151
- CHAPTER 17 153
- 17.3 IGMP Status Screen 154
- Chapter 17 IGMP 155
- Figure 69 IGMP (Status) 155
- Table 35 IGMP (Status) 155
- 17.4 IGMP Bandwidth Screen 156
- 17.5 IGMP Setup Screen 158
- 17.7 IGMP Count Screen 159
- 17.8 IGMP Port Info Screen 160
- 17.9 IGMP Port Group Screen 160
- Table 41 IGMP Port Group 161
- Chapter 17 IGMP 162
- CHAPTER 18 163
- Chapter 18 Static Multicast 164
- CHAPTER 19 165
- 19.3 MVLAN Setup Screen 166
- Chapter 19 Multicast VLAN 167
- Figure 78 MVLAN Setup 167
- Table 44 MVLAN Setup 167
- 19.4 MVLAN Group Screen 168
- Chapter 19 Multicast VLAN 170
- CHAPTER 20 171
- Chapter 20 Filtering 172
- CHAPTER 21 173
- Chapter 21 MAC Filter 174
- CHAPTER 22 175
- Table 49 RSTP Port States 176
- CHAPTER 23 181
- 23.2 RADIUS Screen 182
- 23.3 802.1x Screen 183
- Table 53 802.1x (continued) 184
- CHAPTER 24 185
- Chapter 24 Port Security 186
- Figure 89 Select Ports 186
- CHAPTER 25 187
- 25.3 DHCP Relay Screen 188
- Chapter 25 DHCP Relay 189
- Table 55 DHCP Relay 189
- Chapter 25 DHCP Relay 190
- CHAPTER 26 191
- Table 57 DHCP Snoop Status 192
- Chapter 26 DHCP Snoop 192
- Figure 94 DHCP Snoop Status 192
- 26.4 DHCP Counter Screen 193
- CHAPTER 27 195
- 27.2 2684 Routed PVC Screen 196
- 27.4 RPVC Arp Proxy Screen 199
- Figure 99 RPVC Arp Proxy 200
- Table 61 RPVC Arp Proxy 200
- CHAPTER 28 203
- Chapter 28 PPPoA to PPPoE 204
- Figure 102 PPPoA to PPPoE 204
- Table 63 PPPoA to PPPoE 204
- Chapter 28 PPPoA to PPPoE 205
- CHAPTER 29 209
- 29.3 DSCP Map Screen 210
- CHAPTER 30 211
- 30.2 TLS PVC Screen 212
- Chapter 30 TLS PVC 213
- Figure 107 TLS PVC 213
- Table 67 TLS PVC 213
- Chapter 30 TLS PVC 214
- CHAPTER 31 215
- 31.2 ACL Setup Screen 216
- Chapter 31 ACL 217
- Figure 108 ACL Setup 217
- Table 68 ACL Setup 217
- ACL, ACL Profile Setup 218
- 31.4 ACL Profile Map Screen 219
- Chapter 31 ACL 220
- Figure 110 ACL Profile Map 220
- Table 70 ACL Profile Map 220
- CHAPTER 32 221
- CHAPTER 33 223
- Chapter 33 Syslog 224
- CHAPTER 34 225
- Chapter 34 Access Control 226
- Table 74 SNMP Commands 226
- 34.3.1 Supported MIBs 227
- 34.3.2 SNMP Traps 227
- 34.4 SNMP Screen 228
- Chapter 34 Access Control 229
- Figure 115 SNMP 229
- Table 76 SNMP 229
- Routing Protocol 233
- Alarm and 233
- Management 233
- CHAPTER 35 235
- Chapter 35 Static Routing 236
- CHAPTER 36 237
- Chapter 36 Maintenance 238
- Figure 120 Firmware Upgrade 238
- 36.5 Load Factory Defaults 239
- 36.6 Reboot System 240
- 36.7 Command Line FTP 240
- CHAPTER 37 241
- Chapter 37 Diagnostic 242
- Table 80 Diagnostic 242
- Chapter 37 Diagnostic 243
- CHAPTER 38 245
- 38.2 MAC Table Screen 246
- CHAPTER 39 247
- Chapter 39 ARP Table 248
- Figure 128 ARP Table 248
- Table 82 ARP Table 248
- CHAPTER 40 249
- 40.3 Alarm Descriptions 250
- Chapter 40 Alarm 251
- Chapter 40 Alarm 252
- Table 85 Alarm Event Setup 252
- 40.5 Alarm Port Setup Screen 254
- CLI Commands 255
- CHAPTER 41 257
- 41.4 Commands 258
- Chapter 41 Commands Summary 259
- Chapter 41 Commands Summary 260
- CHAPTER 42 277
- 42.3.1 Log Messages 278
- Chapter 42 Command Examples 279
- 42.4 Isolation Commands 280
- 42.6 Statistics Port Command 281
- Chapter 42 Command Examples 282
- CHAPTER 43 283
- 43.4 Alarm Port Show Command 284
- 43.5 Alarm Port Set Command 285
- 43.6 Alarm Tablelist Command 285
- 43.7 Log Format 286
- 43.10 Alarm XEdit Command 288
- 43.11 Alarm Cutoff Command 288
- 43.12 Alarm Clear Command 289
- Chapter 43 Alarm Commands 290
- CHAPTER 44 291
- 44.1.3 Disable Command 292
- 44.1.4 Server Set Command 292
- 44.1.5 Server Delete Command 292
- 44.1.6 Server Active Command 292
- (Circuit ID) 293
- (Remote ID) 294
- 44.4 DHCP Snoop Commands 295
- Chapter 44 DHCP Commands 296
- Chapter 44 DHCP Commands 297
- CHAPTER 45 299
- 45.4.2 VLAN PVID Command 300
- 45.4.3 VLAN Priority Command 300
- 45.4.4 VLAN Set Command 301
- 45.4.6 VLAN CPU Show Command 303
- 45.4.7 VLAN CPU Set Command 303
- 45.4.9 VLAN Delete Command 304
- 45.5 VLAN Enable 305
- 45.6 VLAN Disable 305
- CHAPTER 46 307
- Chapter 46 MAC Commands 308
- Chapter 46 MAC Commands 309
- 46.3 MAC Count Commands 310
- 46.3.4 MAC Count Set Command 311
- CHAPTER 47 313
- 47.3 IGMP Filter Commands 314
- Chapter 47 IGMP Commands 315
- 47.4 IGMP Bandwidth Commands 316
- Chapter 47 IGMP Commands 318
- 47.8 Multicast VLAN Commands 323
- CHAPTER 48 327
- CHAPTER 49 331
- 49.3 General IP Commands 332
- 49.3.4 Route Delete Command 333
- 49.3.5 Route Show Command 333
- 49.4 Statistics IP Command 334
- CHAPTER 50 335
- 612-51A 336
- 50.4 Firmware File Upgrade 339
- CHAPTER 51 341
- Chapter 51 SNMP Commands 342
- CHAPTER 52 343
- Chapter 52 ADSL Commands 344
- Chapter 52 ADSL Commands 345
- 52.1.8 DSL Port Name Command 348
- 52.1.9 DSL Port Tel Command 348
- 52.2.1 DSL Port Show Command 357
- 52.2.2 Linedata Command 358
- 52.2.3 Lineinfo Command 359
- 52.2.4 Lineperf Command 360
- G.992.3 for more information 364
- Table 98 ToneDiag Command 369
- 52.3 Alarm Profile Commands 370
- CHAPTER 53 375
- 53.3 PVC Channels 377
- 53.3.2 PVC Set Command 378
- 53.4 Priority-based PVCs 379
- 53.6.1 PPVC Show Command 382
- 53.6.2 PPVC Delete Command 383
- 53.7.5 RPVC Set Command 386
- 53.7.6 RPVC Show Command 387
- 53.7.7 RPVC Delete Command 388
- 53.8.2 PAE PVC Set Command 392
- 53.8.3 PAE PVC Show Command 393
- 53.9.2 TLS PVC Set Command 396
- 53.9.3 TLS PVC Show Command 397
- CHAPTER 54 399
- Chapter 54 ACL Commands 401
- 54.2 ACL Assignment Commands 402
- Chapter 54 ACL Commands 404
- Troubleshooting 405
- CHAPTER 55 407
- 55.5 DSL Data Transmission 408
- 55.7 Testing Wiring 409
- Chapter 55 Troubleshooting 410
- Table 105 Wiring Tests 410
- 55.8 Local Server 411
- 55.9 Data Rate 411
- 55.10 Configured Settings 412
- 55.11 Password 412
- 55.12 System Lockout 412
- 55.13 SNMP 412
- 55.14 Telnet 413
- 55.15 Resetting the Defaults 413
- CHAPTER 56 417
- 56.2 Firmware Features 418
- 56.3 Standards Supported 422
- 56.4 Default Settings 423
- PART VII 427
- APPENDIX A 429
- ZyXEL Limited Warranty 430
- Appendix A Legal Information 431
- Appendix A Legal Information 432
- APPENDIX B 433
- Appendix B Customer Support 434
- Appendix B Customer Support 435
- Numerics 439
Related products and manuals for Network switches ZyXEL IES-612-51A
Network switches ZyXEL 4728F User Manual
(491 pages)
(491 pages)
(2 pages)
Network switches ZyXEL GS1920 User Manual
(368 pages)
(368 pages)
Network switches ZyXEL VES-1616F-3X User Manual
(310 pages)
(310 pages)
Network switches ZyXEL XGS-4528F User Manual
(372 pages)
(372 pages)
Network switches ZyXEL GS2200-24 User Manual
(358 pages)
(358 pages)
Network switches ZyXEL ES-3124 User Manual
(337 pages)
(337 pages)
Network switches ZyXEL ES-2108 User Manual
(224 pages)
(224 pages)
© 2020, manymanuals.com. All rights reserved. | 0.425 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals